Press the “ Update ” option using the MMI Control Panel. MMI 3G Console. Scroll down with the big knob and select the source in the menu ( SD 1) MMI 3G source selection. Select the firmware by pressing the big knob once. MMI 3G firmware update version selection. And on the next window select “ Standard ”. In order new 2019 map to fit in 32GB SD do not copy the following folders pkgdb/LIT pkgdb/LIT2 pkgdb/LIT3 You might need GEM (Green engineering menu) activated and use User Defined Mode and manually select all that is under AUDI_MMI3G_ECE if it's not selected. Warning - FW update K0900 is removing the "Emergency Update" option from the "Green A6 / S6 (C6 Platform) Discussion - A6 C6 navi "navigation data are not enabled" - I bought a used Audi a6 c6 with full extra. Only the Navigation is not working, it said navigation data are not enabled It did not have the sd card, so I decided to buy one from ebay (8x0 part numbers 2012 maps). MMI writes correctly the Hello, I was wondering if anyone can suggest steps to identify the fault on Audi A6 AVANT (C6) 2005 MMI high. It went dead out of nowhere. The screen is black, none of the MMI functions are working. Even power button doesn't lit up. I've checked fuses next to the driver seat and in the boot Depending on the version you are upgrading from, you may need to run the 4610 update a couple of times to get all modules updated. And it is recommended that you use a battery charger so the battery does not drain while you are doing it. Reply Like. # 8. AudiWorld Newcomer. Hi I have a audi a6 c6 4f year 2010.Bluetooth version bbt-eu-poo20 d1 am trying to activate the Bluetooth module with vcds like I see on YouTube I have no green menu.so on the vcds I am getting 17-1-1.and not 17-0-1to activate it would you No why.thanks for any help Liam OZXN. 2. I found the answer in this manual. Basically, the Battery Management Control Unit uses: current draw on the battery (measured at the control unit) temperature of the battery (measured at the control unit and transformed by algorythm to what the actual battery temperature should be) voltage of the battery (measured at the positive terminal Audi MMI 2G hidden green menu can be used to change coding & adaptation of Module 07 – MMI 2G Control Head, enable some user interface features and tweak user experience. All that without diagnostic interface like OBDeleven, VCDS. How to access hidden green menu in Audi MMI 2G (A4, A5, A6, A8, Q7) service menu. Watch on. FI: Mmi not working, a6 c6 A6 / S6 (C6 Platform) Discussion Discussion forum for the C6 Audi A6 produced from 2004-present and Audi S6 produced from 2007 - 2011 Community Links MMI buttons are not lighting. I checked fuses in dashboard (drivers side) and in trunk multiple times and they are fine.. Car is a sedan. VCDS Auto Scan: 00-Steering Angle Sensor -- Status: OK 0000. 01-Engine -- Status: Malfunction 0010. 02-Auto Trans -- Status: OK 0000. 03-ABS Brakes -- Status: OK 0000. One part of the driver's seat adjustment not working for you is what draw my attention. Remove the driver's door panel, disconnect everything in there, try starting the MMI. If it works, you can start isolating components. In my case it was a short in the rear view mirror wiring. A6 C6 3.0 Quattro le mans , was wondering any help my MMI stopped working 2 days after buying car screen lights up for about 40secs then turns of I have no fiber optic light going to nothing at the back of car and there dosnt seem to be any power at the control unit at the gear stick any help would be great.

audi a6 c6 mmi not working